View NL10276BC24-14_7871486.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

document number: dod-pp-0048 (1st edition) published date: october 2006 cp(n) ? nec lcd technologies, ltd. 2006 all rights reserved. 1 all information is subject to change without notice. please confirm the sales representative before starting to design your system. tft color lcd module NL10276BC24-14 31cm (12.1 type) xga lvds interface (1port) preliminary data sheet dod-pp-0048 (1st edition) www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 2 introduction the copyright to this document belongs to nec lc d technologies, ltd. (hereinafter called "nec"). no part of this document will be used, reproduced or copied without prior written consent of nec. nec does and will not assume any liability for infringement of patents, copyrights or other intellectual property rights of any third party arising out of or in connection with application of the products described herein except for that directly attributable to mechanisms and workmanship thereof. no license, express or implied, is granted under any patent, copy right or other intellectual property right of nec. some electronic parts/components would fail or malfunction at a certain rate. in spite of every effort to enhance reliability of products by nec, the possibility of failures and malfunction might not be avoided entirely. to prevent the risks of damage to death, human bodily injury or other property arising out thereof or in connection therewith, eac h customer is required to take sufficient measures in its safety designs and plans including, but not limited to, redundant system, fire-containment and anti-failure. the products are classified into three quality grades: "standard" , "special" , and "specific" of the highest grade of a quality assurance program at the choice of a customer. each quality grade is designed for applications described below. any customer who intends to use a product for application other than that of standard quality grade is required to contact an nec sales representative in advance. the standard quality grade applies to the products developed, designed and manufactured in accordance with the nec standard quality assurance pr ogram, which are designed for such application as any failure or malfunction of the pr oducts (sets) or parts/components in corporated therein a customer uses are, directly or indirectly, free of any damage to death, human bodily injury or other property, like general electronic devices. examples: computers, office automation equipment, communications equipment, test and measurement equipment, audio and visual equipment, home el ectronic appliances, machine tools, personal electronic equipment, industrial robots, etc. the special quality grade applies to the products developed, designed and manufactured in accordance with an nec quality assurance program stricter than the standard one, which are designed for such application as any failure or malfunction of the produc ts (sets) or parts/components incorporated therein a customer uses might directly cause any damage to death, human bodily injury or other property, or such application under more severe condition than that defined in the standard quality grade without such direct damage. examples: control systems for transp ortation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, medical equipment not specifically designed for life support, safety equipment, etc. the specific quality grade applies to the products developed, designed and manufactured in accordance with the standards or quality assurance program designated by a customer who requires an extremely higher level of reliability and quality for such products. examples: military systems, aircraft control equipment, aerospace equipment, nuclear reactor control systems, medical equipment/device s/systems for life support, etc. the quality grade of this product is the "standard" unless otherwise specified in this document. www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 3 contents introduction ............................................................................................................................... ................ 2 1. outline ............................................................................................................................... .......................... 4 1.1 structure and princi ple.................................................................................................... ............ 4 1.2 application................................................................................................................ ............................ 4 1.3 features................................................................................................................... ............................... 4 2. general specifications ..................................................................................................................... 5 3. block diagram ............................................................................................................................... ......... 6 4. detailed specifications .................................................................................................................... 8 4.1 mechanical specifica tions.................................................................................................. ......... 8 4.2 absolute m aximum ratings ................................................................................................... ...... 8 4.3 electrical c haracteristics................................................................................................. ....... 9 4.3.1 lcd panel signal processing board ........................................................................................ ................ 9 4.3.2 backlight................................................................................................................ ............................... 10 4.3.3 power supply voltage ripple.............................................................................................. .................... 10 4.3.4 fuse..................................................................................................................... .................................. 10 4.4 power supply vo ltage sequence ............................................................................................. 11 4.5 connections and functi ons for interface pins.............................................................. 12 4.6 position of plug and socket................................................................................................ ...... 13 4.7 connection between receiv er and transmitter for lvds ....................................... 14 4.8 lvds data input map ........................................................................................................ ................ 15 4.9 display colors and data signals ............................................................................................ 16 4.10 display positions......................................................................................................... ................... 17 4.11 scanning directions ....................................................................................................... ............. 17 4.12 input si gnal ti mings...................................................................................................... ............... 18 4.12.1 outline of input signal timings ......................................................................................... .................. 18 4.12.2 timing characteristics .................................................................................................. ....................... 19 4.12.3 input signa l timing chart ............................................................................................... ...................... 20 4.13 optics.................................................................................................................... ................................ 21 4.13.1 optical ch aracteristics................................................................................................. ........................ 21 4.13.2 definition of contrast ratio............................................................................................ ...................... 22 4.13.3 definition of luminance uniformity ...................................................................................... .............. 22 4.13.4 definition of response times ............................................................................................ ................... 22 4.13.5 definition of viewing angles............................................................................................ ................... 22 5. reliability tests ............................................................................................................................... ... 23 6. precautions ............................................................................................................................... ............. 24 6.1 meaning of c aution signs ................................................................................................... ........ 24 6.2 caut ions ................................................................................................................... ............................ 24 6.3 attentions ................................................................................................................. .......................... 24 6.3.1 handling of the product .................................................................................................. ...................... 24 6.3.2 environment .............................................................................................................. ........................... 25 6.3.3 characteristics.......................................................................................................... ............................. 25 6.3.4 other .................................................................................................................... ................................. 25 7. outline drawings ............................................................................................................................... . 26 7.1 front view ................................................................................................................. .......................... 26 7.2 rear view .................................................................................................................. ........................... 27 revision history ............................................................................................................................... ....... 28 www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 4 1. outline 1.1 structure and principle color lcd module NL10276BC24-14 is composed of the amorphous silicon thin film transistor liquid crystal display (a-si tft lcd) panel structure wi th driver lsis for driving the tft (thin film transistor) array and a backlight. the a-si tft lcd panel structure is injected liquid crystal material into a narrow gap between the tft array glass substrate and a color-filter glass substrate. color (red, green, blue) data signals from a host system (e.g. signal generator, etc.) are modulated into best form for active matrix system by a signal pr ocessing board, and sent to the driver lsis which drive the individual tft arrays. the tft array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly, when it is controlled by data signals. color images are created by regulating the amount of transmitted light through the tft array of red, green and blue dots. 1.2 application ? note pc 1.3 features ? lvds interface ? reversible-scan direction ? led backlight type www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 5 2. general specifications display area 245.76 (h) 184.32 (v) mm diagonal size of display 31cm (12.1 inches) drive system a-si tft active matrix display color 262,144 colors pixel 1,024 (h) 768 (v) pixels pixel arrangement bgr(blue dot, green dot, red dot) vertical stripe dot pitch 0.08 (h) 0.24 (v) mm pixel pitch 0.24 (h) 0.24 (v) mm module size 260.0 (w) 200.0 (h) 6.5 (d) mm (typ.) weight 285 g (typ.) contrast ratio 600:1 (typ.) viewing angle at the contrast ratio 10:1 ? horizontal: right side 45 (typ.), left side 45 (typ.) ? vertical: up side 20 (typ.), down side 40 (typ.) designed viewing direction at dps= low or open: normal scan ? viewing direction without image reversal: up side (12 o'clock) ? viewing direction with contrast peak: down side (6 o'clock) ? viewing angle with optimum grayscale ( =2.2): normal axis (perpendicular) polarizer surface clear polarizer pencil-hardness 3h (min.) [by jis k5400] color gamut at lcd panel center 40 % (typ.) [against ntsc color space] response time ton+toff (10% 90%) 25 ms (typ.) luminance at il=20ma 300 cd/m 2 (typ.) signal system lvds 1port (receiver: thc63lvdf84b, thine electronics inc. or equivalent) 6bit digital signals for data of rgb colors, dot clock (clk), data enable (de) power supply voltage lcd panel signal processing board: 3.3v backlight led backlight type: power consumption at il=20ma, checkered flag pattern 4.5 w (typ.) www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 6 3. block diagram note1: relations between gnd (s ignal ground), fg (frame grou nd) in the lcd module are as follows. gnd - fg not connected note2: gnd and fg must be connected to customer equipment?s ground, and it is recommended that these grounds are connected together in customer equipment. note1 note2 lcd panel signal processing board host 3,072 lines lcd panel h: 1,024 3 (r, g, b) v: 768 768 lines vcc gnd dc/dc converter lcd module (product) fuse h-driver fg d0+ d0- 100 d1+ d1- 100 d2+ d2- 100 dps clk+ clk- 100 note1 note2 controller with receiver for lvds v-driver power supply for gradation 47k cathode1-5 anode1-5 5 5 backlight note3 www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 7 note3: backlight in detail anode 1 cathode 1 backlight anode 2 cathode 2 anode 3 cathode 3 anode 4 cathode 4 anode 5 cathode 5 www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 8 4. detailed specifications 4.1 mechanical specifications parameter specification unit module size 260.0 (w) 200.0 (h) 6.5 (d) (typ) note1 mm display area 245.76 (h) 184.32 (v) note1 mm weight 285 (typ.), 300 (max.) g note1: see " 7. outline drawings ". 4.2 absolute maximum ratings parameter symbol rating unit remarks power supply voltage lcd panel signal processing board vcc -0.3 to +4.0 v display signals note1 vd input voltage for signals function signal note2 vf -0.3 to vcc+0.3 v - power dissipation pd 1.1 w forward current il note3 ma backlight pulse forward current ifp note4 ma per one circuit storage temperature tst -20 to +60 c - operating temperature top 0 to +55 c note5 95 % ta 40 c 85 % 40 c 55 c note1: display signals are d0+/ -, d1+/-, d2+/-and clk+/-. note2: function signal 1 is dps. www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 9 note3: forward current note4: pulse forward current note5: measured at center of lc d panel surface (including self-heat) note6: no condensation note7: water amount at ta = 55c and rh = 70% 4.3 electrical characteristics 4.3.1 lcd panel signal processing board (ta = 25 c) parameter symbol min. typ. max. unit remarks power supply voltage vcc 3.0 3.3 3.6 v - power supply current icc - 480 note1 770 note2 ma at vcc = 3.3v permissible ripple voltage vrp - - 100 mvp-p for vcc high vth - - +100 mv differential input threshold voltage for lvds receiver low vtl -100 - - mv at vcm=1.2v note3 terminating resistance rt - 100 - - high vfh 0.7vcc - vcc v input voltage for dps signals low vfl 0 - 0.3vcc v cmos level note1: checkered flag pattern [by eiaj ed-2522] note2: pattern fo r maximum current note3: common mode voltage for lvds receiver ambient temperature ta [ c ] allowable forward current il (ma) duty ratio (%) allowable pulse forward current ifp (ma) www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 10 4.3.2 backlight (ta= 25 c) parameter symbol min. typ. max. unit remarks forward current il - 20 22 ma - forward voltage vl - 28.8 31.5 v at il= 20ma note1: please drive with constant current . note2: the luminance uniformity may be changed depending on the current variation between 5 circuits. it is recommended that the current value difference between each circuit is less than 5%. 4.3.3 power supply voltage ripple this product works, even if the ripple voltage levels are beyond the permissible values as following the table, but there might be noise on the display image. power supply voltage ripple voltage note1 (measure at input term inal of power supply) unit vcc 3.3v 100 mvp-p note1: the permissible ripple voltage includes spike noise. 4.3.4 fuse fuse parameter type supplier rating fusing current remarks 2.0a vcc fcc16202ab kamaya electric co.,ltd. 32v 4.0a note1 note1: the power supply capacity should be more than the fusing current. if it is less than the fusing current, the fuse may not blow in a short time, and then nasty smell, smoke and so on may occur. www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 11 4.4 power supply voltage sequence * these signals should be measured at the terminal of 100 resistance. note1: in terms of voltage variation (voltage drop) while vcc rising edge is below 3.0v, a protection circuit may work, and then this product may not work. note2: display signals (d0+/-, d1+/-, d2+/- and clk+/-) and function signals (dps) must be low or high-impedance, exclude the valid period (see above sequence diagram), in order to avoid that internal circuits is damaged. if some of display and function signals of this product are cut while this product is working, even if the signal input to it once again, it might not work normally. if customer stops the display and function signals, they should be cut vcc. note3: the backlight should be turned on within the valid period of display and function signals, in order to avoid unstable data display. 0ms < t < 35ms valid period off 0ms < t < 35ms on 3.0v 0v 10 s tr < 50ms vcc note1 display signals* function signals note2 toff 50ms 0v 0.3v on www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 12 4.5 connections and functions for interface pins cn1 socket (lcd module side): fi-xb30sl-hf10 (japan aviation electronics industry limited (jae)) adaptable plug: fi-x30 ? (japan aviation electronics industry limited (jae)) pin no. symbol signal remarks 1 vcc 2 vcc power supply note1 3 gnd 4 gnd ground note1 5 d0- 6 d0+ pixel data note2 7 gnd ground note1 8 d1- 9 d1+ pixel data note2 10 gnd ground note1 11 d2- 12 d2+ pixel data note2 13 gnd ground note1 14 clk- 15 clk+ pixel clock note2 16 gnd ground note1 17 gnd ground note1 18 dps selection of scan direction high: reverse scan low or open: normal scan note3 19 gnd ground note1 20 gnd ground note1 21 k1 cathode 1 - 22 a1 anode 1 - 23 k2 cathode 2 - 24 a2 anode 2 - 25 k3 cathode 3 - 26 a3 anode 3 - 27 k4 cathode 4 - 28 a4 anode 4 - 29 k5 cathode 5 - 30 a5 anode 5 - note1: all gnd and vcc termin als should be used withou t any non-connected lines. note2: twist pair wires with 100 (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter. note3: see " 4.11 scanning directions ". note4: see " 4.7 connection between receiver and transmitter for lvds ". www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 13 4.6 position of plug and socket rear view cn1 1 30 side view barcode label name p late label www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 14 4.7 connection between receiver and transmitter for lvds note1: recommended transmitter thc63lvdm83r (thine electronics inc.) or equivalent note2: lsb (least significant bit) ? r0, g0, b0 msb (most significant bit) ? r5, g5, b5 note3: twist pair wires with 100 (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter. note4: input signals to tc4 and tc5 are not used inside the product, but do not keep tc4 and tc5 open to avoid noise problem. host vcc vcc gnd gnd d0- d0+ gnd d1- d1+ gnd d2- d2+ gnd clk- clk+ gnd gnd dps gnd gnd ta0 ta1 ta2 ta3 ta4 ta5 ta6 tb0 tb1 tb2 tb3 tb4 tb5 tb6 tc0 tc1 tc2 tc3 tc4 tc5 tc6 clk in ta- ta+ tb- tb+ tc- tc+ tck- tck+ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 gnd cn1 ra- ra+ rb- rb+ rc- rc+ rclk- rclk+ note3 r0 r1 r2 r3 r4 r5 g0 g1 g2 g3 g4 g5 b0 b1 b2 b3 b4 b5 note4 note4 de clk vcc gnd dps note2 lcd module (product) receiver for lvds equivalent of thc63lvdf84b lcd controller lvds transmitter thc63lvdm83r or equivalent note1 lcd panel signal processing board gnd signal processor vcc dps www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 15 4.8 lvds data input map na: not available d0+ / - d1+ / - d2+ / - r0 g0 r5 r4 r3 r2 r1 r0 g0 g1 b1 b0 g5 g4 g3 g2 g1 b1 b2 de b4 b3 b2 de 1 cycle clk+ cl k - na na b5 r1 g2 b3 www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 16 4.9 display colors and data signals this product can display in equivalent to 262,144 colors in 64 gray scales. also the relation between display colors and input data signals is as the following table. data signal (0: low level, 1: high level) display colors r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 basic colors black blue red magenta green cyan yellow white 000000 000000 111111 111111 000000 000000 111111 111111 000000 000000 000000 000000 111111 111111 111111 111111 000000 111111 000000 111111 000000 111111 000000 111111 red gray scale black dark bright red 000000 000001 000010 : : 111101 111110 111111 000000 000000 000000 : : 000000 000000 000000 000000 000000 000000 : : 000000 000000 000000 green gray scale black dark bright green 000000 000000 000000 : : 000000 000000 000000 000000 000001 000010 : : 111101 111110 111111 000000 000000 000000 : : 000000 000000 000000 blue gray scale black dark bright blue 000000 000000 000000 : : 000000 000000 000000 000000 000000 000000 : : 000000 000000 000000 000000 000001 000010 : : 111101 111110 111111 www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 17 4.10 display positions the following table is the coordinates per pixel (see " 4.11 scanning directions ".). c (0, 0) b g r c( 0, 0) c( 1, 0) ? ? ? c( x, 0) ? ? ? c(1022, 0) c(1023, 0) c( 0, 1) c( 1, 1) ? ? ? c( x, 1) ? ? ? c(1022, 1) c(1023, 1) ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? c( 0, y) c( 1, y) ? ? ? c( x, y) ? ? ? c(1022, y) c(1023, y) ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? c( 0, 766) c( 1, 766) ? ? ? c( x, 766) ? ? ? c(1022, 766) c(1023, 766) c( 0, 767) c( 1, 767) ? ? ? c( x, 767) ? ? ? c(1022, 767) c(1023, 767) 4.11 scanning directions the following figures are seen from a front view . also the arrow shows the direction of scan. note1: meaning of c (x, y) and d (x, y) c (x, y): the coordinates of the display position (see " 4.10 display positions ".) d (x, y): the data number of input signal for lcd panel signal processing board figure 1. normal scan (dps: low or open) c (0, 0) d (0, 0) c (0,767) d (0,767) c (1023, 767) d (1023, 767) c (1023, 0) d (1023, 0) note1 figure 2. reverse scan (dps: high) note1 c (0, 0) d (1023, 767) c (0,767) d (1023, 0) c (1023, 767) d (0, 0) c (1023, 0) d (0, 767) www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 18 4.12 input signal timings 4.12.1 outline of input signal timings ? horizontal signal ? vertical signal note1: this diagram indicates virtual signal for set up to timing. note2: see " 4.12.3 input signal timing chart " for numeration of pulse. display period horizontal display period (thd) de (data enable) note1 vertical display period (tvd) 1 2 34 768 display period de (data enable) note2 note1 www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 19 4.12.2 timing characteristics (note1, note2) parameter symbol min. typ. max. unit remarks frequency 1/tc 60.0 65.0 68.0 mhz 15.385 ns (typ.) duty - - clk rise time, fall time - - ns - setup time - ns clk-data hold time - ns data rise time, fall time - - ns - 19.67 20.676 22.4 s cycle th - 1,344 - clk horizontal display period thd 1,024 clk 48.363 khz (typ.) 13.3 16.666 18.5 ms cycle tv 780 806 - h vertical (one frame) display period tvd 768 h 60.0 hz (typ.) setup time - ns clk-de hold time - ns de rise time, fall time - - ns - note1: definition of para meters is as follows. tc = 1clk, th = 1h note2: see the data sheet of lvds transmitter. www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 20 4.12.3 input signal timing chart horizontal timing vertical timing invalid 1 2 1023 1024 clk de data (r0-r5) (g0-g5) (b0-b5) invalid thd th de data (r0-r5) (g0-g5) (b0-b5) invalid invalid 1 2 767 768 tvd tv tc www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 21 4.13 optics 4.13.1 optical characteristics (note1, note2) parameter condition sym bol min. typ. max. unit measuring instrument remarks luminance white at center r= 0 , l= 0 , u= 0 , d= 0 l 200 300 - cd/m 2 bm-5a - contrast ratio white/black at center r= 0 , l= 0 , u= 0 , d= 0 cr 300 600 - - bm-5a note3 luminance uniformity white r= 0 , l= 0 , u= 0 , d= 0 lu - 1.25 1.40 - bm-5a note4 x coordinate wx 0.263 0.313 0.363 - white y coordinate wy 0.279 0.329 0.379 - x coordinate rx - tbd - - red y coordinate ry - tbd - - x coordinate gx - tbd - - green y coordinate gy - tbd - - x coordinate bx - tbd - - chromaticity blue y coordinate by - tbd - - color gamut r= 0 , l= 0 , u= 0 , d= 0 at center, against ntsc color space c 35 40 - % sr-3 note5 white to black ton - 6 15 ms response time black to white toff - 19 47 ms bm-5a note6 note7 right u= 0 , d= 0 , cr 10 r 35 45 - left u= 0 , d= 0 , cr 10 l 35 45 - up r= 0 , l= 0 , cr 10 u 10 20 - viewing angle down r= 0 , l= 0 , cr 10 d 30 40 - ez contrast note8 note1: these are initial characteristics. note2: measurement conditions are as follows. ta = 25 c, vcc = 3.3v, il =20ma, display mode: xga, horizontal cycle = 1/48.363khz, vertical cycle = 1/60.0hz, dps= low or open: normal scan optical characteristics are measured at lumi nance saturation after 20minutes from working the product, in the dark room. also measurement methods are as follows. note3: see " 4.13.2 definition of contrast ratio ". note4: see " 4.13.3 definition of luminance uniformity ". note5: these coordinates are found on cie 1931 chromaticity diagram. note6: product surface temperature: topf = tbd c note7: see " 4.13.4 definition of response times ". note8: see " 4.13.5 definition of viewing angles ". lcd module (product) 50cm 1 photodetector (bm-5a or sr-3) photodetector (ez contrast) lcd module (product) www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 22 4.13.2 definition of contrast ratio the contrast ratio is calculated by using the following formula. luminance of white screen luminance of black screen 4.13.3 definition of luminance uniformity the luminance uniformity is calculated by using following formula. maximum luminance from to minimum luminance from to the luminance is measured at n ear the 5 points shown below. 4.13.4 definition of response times response time is measured, the lumina nce changes from " black " to " white ", or " white " to " black " on the same screen point, by photo-detector. to n is the time it takes the luminance change from 90% down to 10%. also toff is the time it takes the luminance change from 10% up to 90% (see the following diagram.). 4.13.5 definition of viewing angles luminance uniformity (lu) = contrast ratio (cr) = left upper lower n ormal axis (perpendicular) t u t d t r t l 12 o?clock right 171 512 853 128 384 640 100% 90% 10% 0% ton toff luminance white black www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 23 5. reliability tests (note1) test item c ondition judgment high temperature and humidity (operation) 60 r 2 q c, rh= 60%, 240hours display data is black. heat cycle (operation) 0 r 3 q c } 1hour 55 r 3 q c } 1hour 50cycles, 4 hours/cycle display data is black. thermal shock (non operation) -20 r 3 q c } 30minutes 60 r 3 q c } 30minutes 100cycles, 1hour/cycle temperature transition time is within 5 minutes. esd (operation) 150pf, 150 : , r 10kv 9 places on a panel surface note2 10 times each places at 1 sec interval dust (operation) sample dust: no. 15 (by jis-z8901)) 15 seconds stir 8 times repeat at 1 hour interval no display malfunctions vibration (non operation) 5 to 100hz, 19.6m/s 2 1 minute/cycle x, y, z direction 120 times each directions mechanical shock (non operation) 539m/ s 2 , 11ms x, r y, r z direction 5 times each directions no display malfunctions no physical damages note1: display and appearance are checked under environmental conditions equivalent to the inspection conditions of defect criteria. note2: see the following fi gure for discharge points. ? ? ? ? ? ? ? ? ? www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 24 6. precautions 6.1 meaning of caution signs the following caution signs have very important meaning. be sure to read "6.2 cautions" and "6.3 attentions", after understanding these contents! ! this sign has the meaning that customer will be injured by himself or the product will sustain a damage, if customer has wrong operations. this sign has the meaning that customer will be injured by himself, if customer has wrong operations. 6.2 cautions ? do not touch the working backlight. there is a danger of burn injury. ? do not shock and press the l cd panel and the backlight! ther e is a danger of breaking, because they are made of glass. (shock: to be not greater 539m/s 2 and to be not greater 11ms, pressure: to be not greater 19.6 n ( 16mm jig)) 6.3 attentions ! 6.3.1 handling of the product p take hold of both ends without touching the circuit board when the product (lcd module) is picked up from inner packing box to avoid broken down or misadjustment, because of stress to mounting parts on the circuit board. q do not hook nor pull cables such as connection cable, and so on, in order to avoid any damage. r when the product is put on the table tempor arily, display surface must be placed downward. s when handling the product, take the measures of electrostatic discharge with such as earth band, ionic shower and so on, because the product may be damaged by electrostatic. t the product must be installed without undue stress such as bends or twist. and do not add undue stress to any portion (such as bezel flat area). bends or twist described above and undue stress to any portion may cause display mura. u do not press or rub on the sensitive product surfa ce. when cleaning the product surface, use of the cloth with ethanolic liquid such as screen cleaner for lcd is recommended. www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 25 do not push nor pull the interface conn ectors while the product is working. when handling the product, use of an original protection sheet on the product surface (polarizer) is recommended for protection of product surface. adhesi ve type protection sheet may change color or characteristics of the polarizer. 6.3.2 environment do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases. keep the product in packing box with antistatic pouch in room temperature to avoid dusts and sunlight, when storing the product. in order to prevent dew condensation occurring by temperature difference, the product packing box should be opened after enough time being left under the environment of an unpacking room. evaluate the leaving time sufficiently because a situation of dew condensation occurring is changed by the environmental temperature and humidity. (recommended leaving time: 6 hours or more with packing state) do not operate in high magnetic field. circuit boards may be broken down by it. this product is not designed as radiation hardened. 6.3.3 characteristics the following items are ne ither defects nor failures. response time, luminance and color may be changed by ambient temperature. display mura, flicker, vertical seam or small spot may be observed depending on display patterns. do not display the fixed pattern for a long time because it may cause image sticking. use a screen saver, if the fixed pattern is displayed on the screen. the display color may be changed depending on viewing angle because of the use of condenser sheet in the backlight. optical characteristics may be change d depending on input signal timings. 6.3.4 other all gnd and vcc terminals should be used without any non- connected lines. do not disassemble a product or adjust variable resistors. pack the product with original shipping package, in order to avoid any damages during transportation, when returning the product to nec for repair and so on. www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 26 7. outline drawings 7.1 front view unit: mm note1: the values in pare ntheses are for reference. www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 27 7.2 rear view unit: mm note1: the values in pare ntheses are for reference. www.datasheet.co.kr datasheet pdf - http://www..net/
NL10276BC24-14 data sheet dod-pp-0048 (1st edition) 28 revision history the inside of latest specifications is revised to the clerical error an d the major improvement of previous edition. only a changed part such as functions, characteristic value and so on that may affect a design of customers, are described especially below. edition document number prepared date revision contents and signature 1st edition dod-pp- 0048 oct. 5, 2006 revision contents new issue prepared by approved by t. ogawa checked by signature of writer t. ogawa www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of NL10276BC24-14

	To Download NL10276BC24-14 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .